Peak Deluxe Carbon Fiber Dual Temp Waterproof Universal Seat Heater Kit

This is the latest in Carbon Fiber Seat Heating Technology. These pads are a Quantum Leap over the previous generation of Carbon Fiber pads. The wide carbon fiber strips are sandwiched between a pliable waterproof cover that can be trimmed with a scissor (standard also available). These wide Carbon Fiber Strips have approximately 300% more Carbon Fiber material then the previous honeycomb Carbon Fiber pads which gives you ~300% more heating surface.

Do not confuse these elements with other seat heater kits that claim to be waterproof as long as you put plastic over them (another words your digital camera is waterproof as long as you put it in a plastic bag!).

Carbon Fiber technology is the best seat heating pad material in the marketplace.

The first reason is that Carbon Fiber is pliable and a good conductor of electricity which can be designed to incorporate a variety of shapes which are interconnected and form a grid which can be sewn over. Carbon Fiber will not corrode or break like copper heating elements.

Second, this Deluxe Universal Seat Heater allows the installer to trim the length of the carbon fiber pads or to cut holes in the center of the pads to accommodate any seat design or seat sensor and still provide heat. Pads are cut with regular scissors or razor blade to create any pattern to fit any seat.

Third, the Parallel heating fibers ensure long life and dependability. With conventional, serial seat heaters, any abuse that breaks the heating wire shuts off the entire heater; the same abuse would only render a small portion of our heater inoperative so the driver will still be cozy and warm!

Fourth, the heating elements are completely waterproof (Waterproof Kit Only) & most of the pad (except where power is supplied) is puncture proof.

Fifth, Ultra-thin carbon fibers mean no bulky and uncomfortable wires. Other than the soothing warmth there's nothing to make the driver or passenger think their seats are out of the ordinary!

This kit will install in any seat with a 12 volt electrical system. This kit is for a single seat's back & bottom. This 2 pad kit is designed to install between your seat upholstery (Leather, Vinyl or Cloth) and the padding underneath. Installation may require removal and re-installation of seat and seat covers, as well as basic knowledge of the vehicle's wiring.

You cannot use just 1 element or use the elements alone as replacements to a currently installed kit. Heating Elements must be trimmed around a seat Airbag or Occupant Sensor. Bottom & Back pads are interchangeable.

FEATURES

Illuminated 2-Color Switch

Peak Deluxe Heated Seat Kits are equipped with the latest Switch Technology. This Illuminated 2-Color Dual Temperature High/Off/Low Rocker Style Round Switch has been developed to provide you with the latest switch technology.

New Dual Temperature Control System

An electronic control module (built into wiring harness) regulates the electricity / temperature circulating within the carbon fiber seat heating pad. This system regulates the flow of power in micro-pulses and maintains a narrower temperature range whether in a high or low setting. Example: The high setting will have a constant range between 120°F to 125°F. The low setting ranges between 110°F to 115°F. These respective temperatures are maintained at these respective levels.
• Included in the wiring harness is an advanced solid-state, micro-pulse power regulator that controls the power / temperature of the heating pads. By timing the electrical pulses instead of using a conventional rheostat, less energy is consumed by the controller and more is available for the heating elements.

Backrest & Seat Bottom Heating Pads

Back = 9°x18° Bottom = 9°x15°
These pads have been designed to these dimensions to enable a universal fit in older as well as newer style seats. Pads are approximately 1/32" thick. Either pad can be installed in back or bottom.
• Length can be trimmed to any size, width cannot be trimmed and has to stay at 9"

Quick Connect / Disconnect Flexible System

Peak Deluxe Heated Seat Kits allow you to get rid of unwanted seat heater wiring when you install switches on the side of the seat. Our seat heaters are equipped with quick-release connectors that can reduce your wiring length by 36° eliminating the need to tie up and hide a bunch of wiring.

Quick Heat Up Time

You should start to notice the effect of heat within the first 2 minutes of starting the system in the High temperature setting.

Electrical Specs

Wattage: 24~30 Watts per Pad, 48~60 Watts per seat
Current Draw: 4 Amps on Low Heat Setting and 5 Amps on High Setting per Seat.

Options

Also available in non-waterproof version for $74.95.

PACKAGE CONTENTS (for 1 seat)

1 Waterproof or Standard Backrest Pad 9"x18"

1 Waterproof or Standard Bottom Pad 9"x15"

Pads are approximately 1/32" Thick and each has 2 rows of double stick tape to adhere to seat. Waterproof Pads have a red protective cover and standard pads have a white cover.

1 Electronic Temperature Control Module

1 pre-wired Dual Temp High/Low (off in the center position) Bi-Color Illuminated 3/4" Round Switch

Quick-Lock Cable Ties & Adhesive Insulating Tape

Installation Manual/Guide

WARRANTY

3 Years from date of purchase


2 Wire Installation (Red to +12Volts & Black to Ground) Everything plugs into each other.
Switch is pre-soldered.

Select Waterproof or Standard